No New Notifications

14PCS Bearing Puller Separator Set 2"/3" Splitters Long Jaw Pulley Removal Kit

Sold by TISA CO

Up to 67% Off

Highlights

14PCS Bearing Puller Separator Set 2”/3” Splitters Long Jaw Pulley Removal Kit

Product Details

14PCS Bearing Puller Separator Set 2"/3" Splitters Long Jaw Pulley Removal Kit


14pc Bearing Separator Puller Set 2" and 3" Splitters Remove Bearings KitLong Jaw Gear
Long Jaw Gear

Features:

2 inches and 3 inches bearing separators.

Drop forged and heat treated.

Separator tools are used with bar puller and legs for a wide variety of pulling jobs

The 5"" puller cross-bar with a 6-1/4"" forcing screw or each of the bearing separators may also be used separately or in combination with other pullers or tools.

Blow mold case for storage.


Package Included (14pcs):

Drop Forged Construction

Two Bearing separator jaws (Splitters) - 2"" & 3""

Extension Legs: 5"" - 4pcs

Extension Legs: 4"" - 4pcs

Yoke center adapter: 6"" – 1pcs

Puller Head Bar: 6.9” – 1pcs

Hooks: 2pcs

Forcing screws




Material: Steel, Iron, Plastic

Overall Size:14.5 x 9.4 x 2.4"" (LxWxH)

G.W.: 12.98 Lb

Quantity: 14 PCS

User Manual:
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.



Important Safety Information
Assembly Precautions
1. Assemble only according to these instructions. Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
3. Keep assembly area clean and well lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or when under the influence of alcohol, drugs or medication.

Use Precautions
1. This product is not a toy. Do not allow children to play with or near this item.
2. Use as intended only.
3. Inspect before every use; do not use if parts are loose or damaged.
4. Maintain product labels and nameplates. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.



Specific Safety Precautions
1. Be certain that the separator jaws are evenly set between bearing halves before attempting to separate.
2. Lead Screw(5)should be centered on the shaft where the bearings are being pulled to avoid damaging
shaft or bearing housing.
3. Avoid pinching or scraping the bearing shaft by securely (and squarely) placing the Jaws around the bearing housing.
4. Use care when removing the Lead Screw from the Case to avoid damaging the threads. Pry up from
the ends of the Lead Screw

.

Operating Instructions
Pulling Bearings off Shaft
1. Select the proper size Bearing Separator Jaw (2 or 14) for the bearing size (2.2" ~ 3" or 2") being removed from the shaft.
2. Loosen the Separator Jaw Nuts(3) sufficiently to allow the jaws to catch behind the bearing housing.
3. Using a wrench (not included), begin to evenly tighten the Nuts until the jaws are securely set behind the bearing housing.
4. Screw in both Extension Screws of the same length (4/12 or 6/9) into the Bearing Separator
Jaws as shown below.
NOTE: Do not use Extension Screws of different lengths.
5. Place the 6 inch Yoke (16) over the Extension Screws and tightly secure with Washers (7) and Nuts (3).
6. Screw Lead Screw(5)into the Yoke until it touches the center of the shaft where the bearings are mounted.
7. Using a wrench, turn the Lead Screw clockwise until the bearing housing begins to move off the shaft.
8. Continue turning the Lead Screw until the bearing housing is off the shaft.
9. Remove the Lead Screw by turning it counterclockwise.
10. Remove bearing housing.



Separating Bearing Housings
1. Select the proper size Bearing Separator Jaw (2 or 14) for the bearing size being separated. Refer to the illustration below.
2. Loosen the Separator Jaw Nuts (3) sufficiently to allow the Jaws to catch between each bearing housing.
3. Using a wrench (not included) begin to tighten Nuts until the Jaws are securely set between the bearing housings.
4. Screw in the selected Extension Screws (4/12 or 6/9) as shown below.
5. The Extension Screws allow the user to grip them and add stability while tightening Nuts.
6. Continue tightening Nuts until the bearing housings are separated.
7. When the bearing housings are separated, remove the Bearing Separator Jaw.
CAUTION! Overtightening Separator Jaw Nuts may damage bearings.



Maintenance and Servicing
1. BEFORE EACH USE, inspect the general condition of the Bearing Puller. Check for:
loose attachments
misalignment or binding of moving parts
cracked or broken attachments
any other condition that may affect its safe operation.
If any abnormality is found, have the problem corrected before further use.
2. AFTER EACH USE, wipe off Bearing Puller with clean, moist cloth.
3. Lubricate attachments regularly to ensure smooth operation.
4. Replace attachment if threads begin to wear and it will not attach to other components.
Item Specifics
Brand Unbranded
Number of Pieces 14
Set or Single Item Set
Type Gear Puller
Warranty Yes


14PCS Bearing Puller Separator Set 2"/3" Splitters Long Jaw Pulley Removal Kit

  • Dimensions: 10.0 inches (H) x 10.0 inches (W) x 10.0 inches (L)
  • Weight: 10.0 ounces
  • Made in China

The Fine Print

  • This item is sold through the TISA CO operated by 9944630 Canada Inc.
  • The merchant is solely responsible to purchasers for the fulfillment, delivery, care, quality, and pricing information of the advertised goods and services.
  • The product is new.
  • This is a FINAL SALE; no returns or refunds unless defective.
  • Offer is not eligible for promo codes, but is eligible for Groupon Bucks.
  • Shipping and handling charges will be $9.99.
  • United States (excluding Alaska & Hawaii) Shipments only.
  • Does not ship to PO boxes.
  • Orders are typically delivered in 5-10 business days.
Offer is not eligible for our promo codes or other discounts.

Customer Reviews

Product Picture for Customer Review

14PCS Bearing Puller Separator Set 2"/3" Splitters Long Jaw Pulley Removal Kit

Rate first, then write a review.

There are no user reviews yet. Be the first one to review.
To ensure the quality of reviews, all reviews are screened for spam and content that may be offensive to other people.

Please Sign In or Sign Up to rate or vote

By purchasing this deal you'll unlock points which can be spent on discounts and rewards. Every 5,000 points can be redeemed for $5 Off your next purchase.
Deals of the Day Banner